UD Mobile works with firmware 5.0.16 and greater. Firmware versions lower than 5.0.16 may work but not officially supported and have known issues which are only fixed by firmware update. The latest 5.x firmware now requires a 500 series Z-Wave board. If upgrading from 4.x to 5.x be sure to select firmware which is compatible with your system. Some information contained on this page may be specific to iOS or Android.
At this time (January 2022) UD Mobile does not yet have Geofence capability. It is in development, but no timeline known for when it will be implemented and available for testing or release.
Quick Start Guides
Existing Portal Users
Upon Installation the app will prompt to setup using ISY Portal. Select Yes.
The app will prompt for ISY Portal login. Select Yes. If app prompts for Portal credentials enter your credentials and save. App may also show a dialog with existing Portal accounts. If this is initial installation select Add New Portal Account.
App will then show a list of ISYs on your portal account or a list of ISY Portal accounts. If a list of Portal Accounts is presented select the Portal account which contains the desired ISY. Select the desired ISY.
Select SAVE at the top right. Then select YES when prompted to synchronize. Wait for synchronization to complete. After synchronization the app will be ready to use on remote connections.
Adding Another ISY (Existing Portal Users)
These instructions assume the ISY is already linked to ISY Portal.
Select Settings-Tab > Systems > Add (top right).
The app will prompt for ISY Portal login. Select Yes. If the ISY is using the same Portal Account as your previously linked ISY(s) select the existing Portal Account from the list. If the ISY is using a different Portal account select Add New Portal Account.
After Portal Account has been selected the app will show a list of available ISYs. Select the desired ISY to add to the app.
Remote connection on UD Mobile can be achieved in 3 scenarios.
First is our managed method using ISY Portal. ISY Portal has competitive prices of $23 for the first 2 years and renewals cost of $20 for two years (prices current as of 06/2021). If your ISY has not been associated with the ISY Portal in the past we offer a 30 day free trial. ISY Portal Installation instructions can be found here https://wiki.universal-devices.com/index.php?title=ISY_Portal_Installation_Instructions
Second is an unmanaged direct connection. The unmanaged method requires a Trusted CA Signed SSL Certificate. The Trusted SSL CERT is required for reasons stated below in App Transport Security. Instructions on adding a CERT to your ISY can be found here: https://www.universal-devices.com/docs/production/ISY994%20Series%20Network%20Security%20Guide.pdf . There are methods to add a Self Signed CERT to the Trusted Key Store on Android, however it is beyond the scope of our support and may require root on some devices.
Finally a local connection can be established on a remote network if running a VPN Server on the same local network as the ISY. To use this method select "Only use Local Connection" in the local connection settings. Setting this option will instruct the App to ignore remote connection settings and only use the local network.
App Transport Security (ATS) iOS
App Transport Security (ATS) is disabled by iOS for local loads (1), for this reason Local Connections do not need a Trusted CERT, ATS requires a Trusted CERT for Remote Connections. While it is possible for the apps to disable ATS it would make all connections less secure and we would have to meet the exception requirements (2) during app review which we likely do not meet.
(1) https://developer.apple.com/documentation/bundleresources/information_property_list/nsapptransportsecurity/nsallowslocalnetworking " ATS doesn’t block local loads by default in newer versions of the OS"
"The app must connect to a server managed by another entity that doesn’t support secure connections." Portals provided by UDI and Third parties support secure connections, and UDI controls the firmware. So, this does not apply. Apple has also mentioned this will be removed in the future.
"The app must support connecting to devices that cannot be upgraded to use secure connections, and that must be accessed using public host names.". ISY firmware does support secure connections, so this exception does not apply.
Local Connections and Local VPN
First is using a local connection along with a remote connection. This will require that "Only use Local Connection" setting is switched off, then add your local WiFi network(s) in System Network Relations. Linking a WiFi Network will instruct UD Mobile to use the Local Connection Settings when your device is connected to a linked network. Please note that this feature requires access to find location so the app can read WiFi networks. If the WiFi information is not populated, after accepting permissions prompt, or is populated with "<unknown ssid>" then location permissions are missing or location has been turned off at the device level. Enable location at the device level by going to to the settings page for the Android device then selecting Location. Enable permissions at the app level by long clicking the app icon then selecting App Info > Permissions > Location, Use precise location must be enabled along with "Allow only while using the app".
Note that the Local IP Address must be fully qualified starting with "http://", also be sure there is no "/" at the end of the address.
If migrating your current ISY setup to a new ISY/Polisy all that is needed is a change of Remote and Local URLs. First backup UD Mobile in case of errors this way Favorites and User Preferences will not be lost. Local Connection change involves changing the Local IP Address, Port, Username, and Password. Portal URL change would involve hitting the delete button in the Systems Portal window, then selecting the Add button, then select your Portal Account, then select the replacement system from the list of ISY connected to ISY Portal. Only nodes with the same Node Address will remain on UD Mobile after migration. If not migrating from a backup or if nodes are manually linked with a new Node Address, then Favorites will be removed on synchronization. Some versions of UD Mobile will prevent synchronization if UUID (the unique id of the system hardware) does not match, the UUID can be cleared at the bottom of Advanced Settings.
Backup and Restore
Backing up the UD Mobile App will save all App Systems, Favorites, and Customizations.
iOS will allow backup to local storage and iCloud, however will only allow restore from a local backup. If your iOS backup was saved to iCloud, go to Apple's Files App then go to iCloud, locate the UD Mobile backup, then long press and select Copy (or Move), then back out to the "Browse" screen and select "On My Phone", then paste the backup file into your iPhone local storage, the backup should now be available for restoration.
See "All Platforms" below for more information.
Android (Only Google's variant tested) will allow backup and restore from local storage and cloud providers such as Google Drive. Android cloud providers can be accessed by clicking the menu in the System File picker, the System file picker should show registered cloud providers.
See "All Platforms" below for more information.
If restoring over a configured app setup go to Settings-Tab > Backup. If restoring to a new device or new installation select cancel when prompted to add Portal Account, enter a temporary System Name, then select Save. When UD Mobile prompts for synchronization select Cancel. Note that errors may be presented as the there are no links to systems. Now go to Settings-Tab > Backup, then select Restore.
Local, Remote, and Portal passwords may need to be reset after import, passwords may persist if backup is imported on the same device but is dependent on the device secure key store. If having trouble with Remote Portal connections please logout all ISY Portal Accounts (Settings-Tab > ISY Portals Accounts) then re-enter the Portal Account in for each System (Settings-Tab > Systems). Currently iOS and Android backups are not compatible with the other platform. Amazon Android and Google Android backups are compatible with each other.
Backing up the UD Mobile App will save all App Systems, Favorites, and Customizations. Backups can be saved from Settings-Tab > Backup. See platform specific backup instructions below.
iOS will allow backup to both local storage and iCloud (See "Restore: above for iCloud backup restorations). After selecting "Backup" navigate to the desired directory then select "Move" on the top right of the screen.
Android (Only Google's variant tested) will allow backup to local storage and cloud providers (i.e. Google Drive). Android cloud providers can be accessed by clicking the menu in the System File picker, the System file picker should show registered cloud providers.
The initial home tab screen will show a list of the users ISYs. Clicking an ISY will show the “Devices and Scenes”, “Network Resources, “Variables” and “My Programs” folders.
Clicking on a folders will show the folder contents, clicking on a node will show the Node’s Dashboard (see Node Dashboard). There may be additional options which are selectable on the right side of a Node list item, see the Node Type below for descriptions and actions. Some Node Types have an Action Indicator displayed at the top left of a Node’s icon (left side), see the Node Type below for descriptions and actions.
All nodes including ISYs and folders can be show/hidden by clicking the edit icon (pencil) at the top of the screen then clicking the add/remove icon to the left of the list item. Note that some Node Types have additional edit functions, see the Node Type below for edit functionality.
Devices and Scenes
Clicking on the “Devices and Scenes” folder will show the user the file structure as shown in the Admin Console (AC). The file structure can be change by the user from UD Mobile or the AC. If changes to file structure are made from the Admin Console, then users will have to synchronize UD Mobile from the “Devices and Scenes” folder by pressing the synchronize icon at the top right of the screen.
Edit a Node by clicking the edit icon then clicking the node in the list. The Edit dialog will be presented with edit options if they exist. Currently not all options are available from UD Mobile, please use the Admin Console for access to all available edits.
Grouped Nodes can be shown by clicking the expand icon on the right side for a node item. The expand icon will only be presented for nodes which have grouped children. If a node has grouped children but all child nodes have been hidden, the user must unhide the child nodes by clicking the edit icon to view children.
The Node Toggle Indicator (Action Indicator) is a filled or empty circle at the top left of the Node’s icon. The Toggle Indicator will only show for nodes which accept on/off (DON/DOF) commands. If UD Mobile has NOT received status for the node from the ISY then the Toggle Indicator will not be show until the node’s status is received. Node status is needed to determine if an on or off command should be sent. If UD Mobile does not have the node’s status clicking on the node’s icon will open the Node’s Dashboard (see Node Dashboard).
Clicking on a Node will show the Node’s Dashboard (see Node Dashboard).
Clicking the “Network Resources” folder will show an alphabetical list of Network Resources. Clicking on a Network Resource will show the Network Resources’ Dashboard (see Node Dashboard).
Clicking on the Network Resources’ icon (left side) will execute the Network Resource. An Action Indicator is shown next to the Network Resources’ icon to indicate it is actionable.
Network Resource Edits are currently not available from UD Mobile, please use the Admin Console then synchronize UD Mobile with ISY.
Clicking the “Variables” folder will show the “Integer Variables” and “State Variables” folders. Clicking on either variable-type folder will show an alphabetical list of the variable-type. Clicking on a variable will show the Variable’s Dashboard (see Node Dashboard)
Variable Edits are currently not available from UD Mobile, please use the Admin Console then synchronize UD Mobile with ISY.
Programs (My Programs)
Clicking the “My Programs” folder will show the user the Program file structure as shown in the Admin Console (AC). Currently the file structure must be changed in the AC then synchronized to UD Mobile by clicking the synchronize icon at the top right of the screen.
The Program Toggle Indicator (Action Indicator) is a filled or empty circle at the top left of the Program’s icon. The Toggle Indicator will show if the program is running or stopped, clicking the Program’s icon will toggle this action. The Toggle Indicator will only show if UD Mobile has the Program’s status. UD Mobile does not request Program status on app launch by default. To request Program status on app launch, go to Settings-Tab > Systems > Your-System-Name > Advanced-Settings > Program-and-Variable-Settings then toggle Request-Status-of-all-Programs. Please see Favorite Examples for custom program toggle (i.e. run if/else)
Program Edits are currently not available from UD Mobile, please use the Admin Console then synchronize UD Mobile with ISY
Show Favorites at launch
Setting the default launch preference to the Favorites Tab is dependent on platform.
Go to Settings-Tab > Global User Preferences > Launch Preference
There is a know bug when using UD Mobile with a Mac M1 were setting the Global User Launch Preference to anything other than Default will result in the app crashing. This includes imported backups. If you set the launch preference on a Mac M1 or imported a backup with this setting, you must delete the folder named "UD Mobile" in Finder. The app will not launch until this folder is deleted. To import a backup which has the launch preference please change the launch preference, swipe app from recents (and verify setting is no longer functional), then export the backup.
Long press the app icon on the home screen, then long press "Favorites", then drag to the home screen. Note some third party launchers may not show "Favorites" with long press and may require another method to obtain the shortcut. If the "Favorites" shortcut is not available search/ask for "dynamic shortcuts" from the launchers creator.
Add New Favorite
Go to the Favorites Tab. Select add ("+") at the top of the screen. This will open the Favorites Editor Screen.
Custom Name (optional)
Adding a Custom Name will override the Display Node name if available.
Favorites Type allows the user to choose click actions for a favorite item.
- Node Type will display an ISY Node and requires the user to select a Display Node (below). Favorites of Type Node have 2 Interaction Types; Toggle and Open-Dashboard. Interaction Types can not be defined by the user. See Toggle Indicators below. For custom toggle please use Command Type along with an ISY Program which has your toggle preferences in the IF section, then select IF as the command (program may need to be disabled in ISY to prevent IF trigger).
- Folder Type will act as a folder allowing the user to add additional favorites inside. Favorites of Type folder also allow for an optional display node which inherits toggle ability from Node Type (above).
- Command. This Type will allows users to specify any number of Node Commands. Pressing a Favorite of Type Command will execute the defined commands. Favorites of Type Command also allow from an optional Display Node, the display node does not inherit toggle ability. The Display Node does not have to match Command Nodes. See Commands below.
- Status. Favorites of Type Status do not have clickable actions.
- Empty. Favorites of Type Empty will create an invisible tile. Empty tiles will be shown in Edit Mode for editability.
Optional Icon. If not set default will be used. If the Display Node (below) is set an the Display Status (below) has an Individual Status Mappings (see Individual Status Mappings) the Favorites Icon has lower priority to Individual Status Mappings with icons.
Optional Icon Color (Currently Android only). If the Display Node (below) is set and the Display Status (below) has an Individual Status Mappings (see Individual Status Mappings) the Favorites Color has lower priority to Individual Status Mappings with color values. Hex color is 6 character hex prefixed by "#" (i.e. #808080). Eight character hex codes may be accepted with the first 2 characters representing alpha. Alpha color may show the original icon color under the user input color.
The node which will be displayed. During Display Node selection an expand (downward chevron) icon next to a node indicates that the node has grouped children (grouped nodes), to see the children press the expand Icon. The Display Node can be cleared by pressing the delete (trash icon) during Display Node selection.
After a node has been selected the Display Status will be shown (i.e. Status, On-Level, Ramp-Rate, ect.). This will allow users to change the default display status.
Node Toggle Indicator
The Node toggle indicator will only show for Favorites which have (#1) "Status" selected as the Display Status, and (#2) the selected node must accept on/off commands. Also (#3) if the App has NOT received a status for the node from the ISY the toggle indicator will not be show until the node's status has been received. Node status is needed to determine if an on or off command should be sent to the node. If the App has NOT received a status for the node, clicking the Favorite item will open the Node's Dashboard which shows all status values and controls for the selected node.
Program Toggle Indicator
The Program toggle indicator will only show for Favorites which have (#1) "Status" selected as the Display Status. Also (#2) if the App has NOT received a status for the program from the ISY the toggle indicator will not be show until the program's status has been received. Program status is needed to determine if the Run or Stop command should be sent to the program. If the App has NOT received a status for the program, clicking the Favorite item will open the Program's (Node's) Dashboard which shows all status values and controls for the selected program. To receive program status values on App startup go to Settings-Tab > Systems > Your-System-Name > Advanced-Settings > Program-and-Variable-Settings then toggle Request-Status-of-all-Programs.
This will be shown if Command is selected as the Favorite Type. To add a command select the add (plus) icon next the the Commands header. Note that to preserve database integrity, the app will prompt to save for new favorites, if the app does not automatically open the Command Selection dialog press the add icon again. Select a node (similar to Display Node above). After a node has been selected the command dialog will show a list of available commands. Note that a menu (three dots) next to a command indicate that the command supports no-parameter and parameter execution (i.e. ON or ON-to-50%). If a command requires parameters or if the parameter option (menu) was selected the Parameters dialog will be show. After entering any parameter adjustments select save. Currently commands support deletion not editing.
Select Save at the top of the screen.
Go to the Favorites Tab. Select Edit (pencil icon) at the top of screen, then click the Favorite item for Edit Options. When edits are finished click the edit (pencil icon) at the top to finish editing.
Go to the Favorites Tab. Select edit (pencil icon) at the top of the screen. Click the Favorite item. Select "Delete".
Icon Colors can be changed at the Global, Individual, and Favorites levels. Global and Individual Color mappings can be set to match node status values. Hex color is 6 character hex prefixed by "#" (i.e. #808080). Eight character hex codes may be accepted with the first 2 characters representing alpha. Alpha color may show the original icon color under the user input color. For installers setting colors for users please follow WCAG Guidelines. Generate WCAG colors at http://colorsafe.co/ with a off white (#fffdff) background.
Change favorite colors by clicking edit at the top of the favorites screen then click the desired node and select Edit. Favorites Colors have the lowest color priority and is intended for favorites folders which will not have a status value.
Change global colors based on node values (Null/Zero/Positive) from Settings-Tab > Global-User-Preferences. Global Mapped Colors have a lower priority than Individual Mapped Colors and have a higher priority to Favorites Mapped Colors.
Individual Status Mappings
Change Individual Status Mappings from the Home/Favorites screen. Click the edit button, then click the desired node, then click Configure Colors/Values/Icons.
Individual Status Mappings can change a node icon, color, value, value-prefix, and value suffix based on the status value.
Value comparisons include Null, Equal-to, Greater-than-or-equal-to, Less-than-or-equal-to, and Not-Equal-to. The app will only return one mapped value even if multiple mappings overlap. Value mappings are evaluated in the following order with the first matched being returned. Value Mapping order: Equal, Greater-than-or-equal-to (descending value order; highest comparison value will be matched), Less-than-or-equal-to (ascending value order; lowest comparison value will be matched), Null, Not-Equal-To (descending value order; highest comparison value will be matched).
(optional) If not set the default will be used. If set this will override Favorite icons.
(optional) hex color code. This will change color for both defined and default icons. This has the highest priority of all color settings (Global/Favorites)
(optional) Sets a name for a status value. i.e. if value equals 0 (0%) show as the word OFF.
(optional) Set a prefix in front of a value. i.e. put $ in front of a variable value.
(optional) Set a suffix behind a value. i.e. put % behind a variable which is used to track lights or the degrees sign behind a variable used to track temperature.
Lock all top bar action items, Admin Tab Items and Settings Tab Items. Only the Global User Preferences item will be active on the Settings Tab and only the Lock Edits available to change with password.
Favorite Custom Toggle
The following is an example of adding a custom toggle for a door lock, but the process is similar for all nodes/programs/variables. A door lock is used in this example as it does not support On or Off commands, so the app will not show a toggle indicator and will only open to the Node's Dashboard when clicked on the Favorites Screen.
First we must create a Program in the Admin Console (Program creation not yet available from UD Mobile). See Program Notes in program image. The program must be disabled to prevent unintended behavior.
In UD Mobile create a new favorite. Change the Type to Command, and set the Door Lock as the Display Node. Add The program created above as a Command Node and select "Run If" as the Command. Note this Favorite was given the Custom Name "Back Door" which will override the original Node Name.
We now have a Favorite item which can toggle the "Back Door" lock. Also because we have a Display Node there is a menu (three dots) which will open the Node's Dashboard, which can be great if the lock is jammed and we must use the unlock control as the toggle will always try to lock in the program created above.
Show/Hide Status and Commands
From the Node's Dashboard click the edit icon (pencil on top). Now press the add/hide (+/-) buttons to the left of the status or button.
Move Status and Commands
From the Node's Dashboard click the edit icon (pencil on top). Now long press the move icon (three lines) on the left side of the status or button. Note that status and buttons are grouped and can only be moved within the same group.
Access Polyglot Cloud (PGC) from the Admin Tab of UD Mobile by clicking the "Polyglot Cloud" list item.
If UD Mobile has more than one ISY Portal linked the user will be presented with a dialog to pick the desired ISY Portal.
If the users ISY Portal Account has more than one ISY the user will be presented with a dialog to pick the desired ISY.
The Polyglot Cloud (PGC) Screen will show a list of installed Node Servers. Only Cloud Node Servers can be edited on the PGC Screen.
Add PGC Node Server
Add a new Node Server from the Polyglot Cloud Store. The PGC Store can be accessed from the Polyglot Cloud Screen by clicking the add (plus) icon at the top right.
Clicking on a Node Server in the PGC Store will take the user to the Node Server’s Store Dashboard. Add the Node Server by clicking “install” at the bottom of the screen. Note that a Node Server must be removed from the Node Servers Dashboard page (see Edit a PGC Node Server). Once the Node Server is added the user may need to add or edit parameters and start the Node Server. Parameter Edits and Start/Stop functions can be found on the Node Servers Dashboard Page. When starting a PGC Node Server please allow a few minutes for the Node Server to initialize after pressing the start button.
Edit PGC Node Server
Status indicators for PGC Node Servers will show Red for Stopped, Green for Started, and Yellow if Started with Notices.
Edit a PGC Node Server by clicking the Node Server in the list. This will present the Node Server Dashboard which has Start, Stop, Update and Delete Functions.
Clicking on Configuration will take the user to the Node Server Configuration Screen. The Configuration Screen allows users to add, edit, or remove parameters.
Edit a parameter by clicking the parameter in the list, then update the value, then press save.
Remove a parameter by clicking the parameter in the list then clicking the delete icon (trash) at the top right of the Edit Parameter dialog.
Add or edit your Alexa Spoken configuration from Admin Tab > Alexa or from the Node Dashboard by clicking the voice icon at the top of the screen.
Clicking Systems on the Settings Tab will show all linked ISY/Polisy Systems
Clicking on a System in the Systems List will open the System Edit Screen for the selected ISY/Polisy. Clicking on the add "+" icon on the top right will open the Add System screen.
Required System name. System Name must be unique from any other system names in the App. System Name is populated automatically if your ISY is selected from ISY Portal, but must be entered manually if not using ISY Portal. System name will show as a list item on the Home Tab. Changing System Name requires synchronization to change the Home Tab list item name.
Remote Connection Settings
See Quick Start Guides above.
Local Connection Settings
See Quick Start Guides above.
Program And Variable Settings
Enabling any item in the section will request status for the selection when the app is started. Requesting the status of all Programs and/or Variable may cause a longer delay in status population when opening the app.
Disabling this setting will instruct UD Mobile to not start a subscription with the ISY, so no status values will be requested when the app is opened. This is intended for developers with multiple Systems and the user would like to disable the System when not testing.
Currently Android Only. Global Subscription Duration affects all systems for UD Mobile. This sets the duration in minutes of the subscription to your ISYs. The app will not close the subscription until the Subscription Duration time has passed or when the operating system requests resource, whichever comes first. Setting this number to \"0\" will close the subscription as soon as UD Mobile is paused and the subscription will have to be reestablished to get node status values. Setting this to a negative number will leave the subscription open until the operating system is low on resources. Please note that the longer the subscription duration the more data and battery consumed by UD Mobile, a shorter duration may cause longer delays for status values when the app loses focus. While the subscription is active UD Mobile will show a notification and may show an app icon badge. Android requires developers to notify users with a notification when an app is using resources in the background, most android devices will allow users to ignore notifications based on type.
Notifications can be sent via network resources, PG3 Node Server coming soon. Node server will use existing email/notification framework available in ISY Admin Console and UD Mobile, however this feature is only available on IoP (ISY on Polisy). Network Resource method available to all ISY users on 5.x with an ISY Portal Account.
PG3 Node Server Setup
Coming Soon. Not yet implemented.
Network Resources Setup
Note: Network Resource creation is currently not available in UD Mobile, so the Admin Console must be used.
1) Click the bottom Notifications Tab in UD Mobile.
2) Click the settings (gear icon) at the top of the notifications tab main screen. If you have linked more than one ISY Portal account (unlikely for most users) you will be prompted to select an ISY Portal Account. The screenshot below shows notification settings.
3) Use the COPY button to copy your API key. Then send a copy of the key to your PC (i.e. email to yourself).
4) From the Admin Console Click Configuration-Tab -> Networking-Tab -> Network-Resources-Tab. Then Add a new Network Resource.
- Protocol: https | POST | Host = my.isy.io | Port = 443 | Path = /api/push/notification/send | Mode = Raw Text
- Header: Add x-api-key with the value as your API Key copied from UD Mobile. This is a manual entry not available from the dropdown menu.
- Body: title=message_title&body=message_body where message_title and message_body are replaced by your desired title and body values.
- Click update then save, then save all network resources. Finally press TEST to send the notification.
The network resource should look similar to the image below, with required replacements.
1) Follow instructions above to create a notification.
2) From the Notification-Settings in UD Mobile click ADD next to groups and create a new group.
3) Click any device in the Devices section then enable the group in the Group Membership section.
4) Write down the Group Id from UD Mobile. The group ID is in parenthesis next to the group name in UD Mobile. The group name and id may be the same.
5) In the Admin Console add "groupid=group_name" to the body of the network resource, where group_name is replaced with the group ID.
6) Save the network resource, then save all network resources, then test.
If your API key is compromised, the RESET button will invalidate the current API key and return a new key. The Devices section will list all mobile devices linked to the Portal Account. Clicking on a Device will allow users to enable/disable/delete the mobile device, enable/disable device membership in groups, and send test notifications. Add groups by clicking the ADD button next to the group header. Clicking on a group will allow group deletion. The instructions below will send notifications to all Active devices.
The "UD Notifications" group can not be deleted from UD Mobile and is intended for sending notifications from UD, such as notifying the user when their ISY is no longer communicating with ISY Portal. UD Notifications have not been implemented as of 06/10/22.
When a Device is deleted from ISY Portal and has an active UD Mobile installation the device will be re-added automatically. This feature is intended to delete old devices, to exclude a device from receiving notifications please click the device in Notification Settings then disable.
The UD Mobile Notification-Tab must be clicked once before the device is available to ISY Portal, so please instruct all family members to click this tab after updating to a version supporting this feature.
Note: Node Server developers should check Node Server functionality with UD Mobile prior to release. UD Mobile has error checking which may be different than the Admin Console. Below are a few common errors and error messages.
Node Status Relation Cursor is empty
This is usually related to a NodeDef Accepts Param init value set to a Status value that does not exist
Example: init="GVP". GVP is not a defined Status ID.
<nodeDefs> <nodeDef id="controller" nodeType="139" nls="ctl"> <editors /> <sts> <st id="ST" editor="bool" /> </sts> <cmds> <sends /> <accepts> <cmd id="DISCOVER" /> <cmd id="REMOVE_NOTICES_ALL" /> <cmd id="UPDATE_PROFILE" /> <cmd id="DEBUG"> <p id="" editor="DEBUG" init="GVP"/> </cmd> </accepts> </cmds> </nodeDef>